Product Overview
SA-410 is a dry powder latex-modified Portland Cement Based Product designed for use as a stone
adhesive to adhere man made stone products to properly prepared substrates. It requires water only
to bring the product to a smooth workable consistency.
Features / Benefits
Dry bagged product
Water based
Consistent batching
Factory blended
Easily stored in cold climates
Mix only the quantity needed
Color consistency
Convenient - just add water
Increases production due to high adhesion properties
Properties
Neutral color
Fine Aggregates
Portland Cement
Proprietary polymer blend
Coverage
Approximately 25 square feet per bag as an adhesive
Recommended Substrates
SA-410 is designed to adhere man made stone products to clean masonry walls or walls prepared
with wire lathe and a portland cement base coat layer. Check with local building officials about local
codes and drainage planes behind the system to allow vapor or moisture drainage.
Preparation
Surface must be clean, dry, structurally sound, and free from dirt, grease or coatings that may inhibit
adhesion. Temperature must be 40 degrees or higher for a period of 24 hours after installation of the
stone product. This also applies if you are using the SA-410 as a joint filler.
Hazard Statement
Harmful if swallowed. Causes
moderate eye irritation. Prolonged
skin contact may cause irritation.
Wash thoroughly after handling. In
case of eye contact flush
immediately with cool water. If
skin or eye irritation persists seek
medical assistance.
Warranty
The manufacturer warrants this
properly handled and installed
product to be free from
manufacturing defects from date of
purchase for a period of five years.
If it is shown that the product is
defective when installed by a
competent installer / applicator, the
manufacturer’s liability under this
warranty is to supply replacement
product. There are no other
warranties expressed or implied
and the manufacturer or
manufacturer’s representative
shall determine the remedies. We
make no other warranties and
expressly disclaim any warranties
of merchantability or fitness for a
particular purpose. See full
warranty schedule in our product
literature submittal package.
Limitations
Protect from freezing. Do not apply
in temperatures above 110-F or
below 40 F. The ambient and
surface temperature must remain
within these temperature ranges
until fully cured (minimum 24
hours). Protect all work from
inclement weather until fully
cured.
Do not add any other materials to
this product without written
permission from the manufacturer.
This is not a finished product and
must have a finish layer applied.
Instructions
Mixing
1. Prepare each bag in a 5 gallon(19 liter) container,
which is clean and free of foreign substances. Do not
use a container which has contained or been cleaned
with any petroleum- based product.
2. Begin with 1.5 gallons (5.6 liters) of clean potable
water Prepare each bag in a 5- gallon (19 liter)
container,.
3. Slowly add the product in small increments to the
water while mixing well with a jiffy-type mixer to a
homogenous consistency.
4. Mix for a minimum of 3 to 5 minutes. Additional
water or material may be added to adjust
workability and desired consistency.
5. Let mixed material stand to allow it to take it’s
initial set for 5 – 10 minutes.
6. Re-mix the material adding enough water to reach
the desired consistency. Do not over mix.
Application
1. For use as an adhesive SA-410 shall be applied to the
back of stone which shall be applied to properly
prepared substrates with enough product to promote
total adhesion. Allow the SA-410 to completely cure
(24 hours is recommended) before filling joints.
2. For use as an adhesive we recommend a margin
trowel or similar type trowel to fully cover the back
of stone. A small amount of SA-410 should be visible
squeezing out from edges of the stone.
3. For use to fill joints in between stones it is
recommended to use a vinyl bag with applicator tip
to squeeze the mixture into voids between stones.
Allow to dry to touch before tooling or raking the
joints. Finish up by brushing with a sift brush or
slicking joints with a slicker tool.
Clean-up
Use fresh water to clean tools or droppings before product
dries.
Distributed by:
Stucco Depot llc
150 North Plains Industrial Rd.
Wallingford, CT 06492
203-430-9186
www.stuccodepot.org
stuccodepot.org@gmail.com