Product Overview

SA-410 is a dry powder latex-modified Portland Cement Based Product designed for use as a stone

adhesive to adhere man made stone products to properly prepared substrates. It requires water only

to bring the product to a smooth workable consistency.

Features / Benefits

Dry bagged product

Water based

Consistent batching

Factory blended

Easily stored in cold climates

Mix only the quantity needed

Color consistency

Convenient - just add water

Increases production due to high adhesion properties

Properties

Neutral color

Fine Aggregates

Portland Cement

Proprietary polymer blend

Coverage

Approximately 25 square feet per bag as an adhesive

Recommended Substrates

SA-410 is designed to adhere man made stone products to clean masonry walls or walls prepared

with wire lathe and a portland cement base coat layer. Check with local building officials about local

codes and drainage planes behind the system to allow vapor or moisture drainage.

Preparation

Surface must be clean, dry, structurally sound, and free from dirt, grease or coatings that may inhibit

adhesion. Temperature must be 40 degrees or higher for a period of 24 hours after installation of the

stone product. This also applies if you are using the SA-410 as a joint filler.

 

Hazard Statement

Harmful if swallowed. Causes

moderate eye irritation. Prolonged

skin contact may cause irritation.

Wash thoroughly after handling. In

case of eye contact flush

immediately with cool water. If

skin or eye irritation persists seek

medical assistance.

Warranty

The manufacturer warrants this

properly handled and installed

product to be free from

manufacturing defects from date of

purchase for a period of five years.

If it is shown that the product is

defective when installed by a

competent installer / applicator, the

manufacturer’s liability under this

warranty is to supply replacement

product. There are no other

warranties expressed or implied

and the manufacturer or

manufacturer’s representative

shall determine the remedies. We

make no other warranties and

expressly disclaim any warranties

of merchantability or fitness for a

particular purpose. See full

warranty schedule in our product

literature submittal package.

Limitations

Protect from freezing. Do not apply

in temperatures above 110-F or

below 40 F. The ambient and

surface temperature must remain

within these temperature ranges

until fully cured (minimum 24

hours). Protect all work from

inclement weather until fully

cured.

Do not add any other materials to

this product without written

permission from the manufacturer.

This is not a finished product and

must have a finish layer applied.

 

Instructions

Mixing

1. Prepare each bag in a 5 gallon(19 liter) container,

which is clean and free of foreign substances. Do not

use a container which has contained or been cleaned

with any petroleum- based product.

2. Begin with 1.5 gallons (5.6 liters) of clean potable

water Prepare each bag in a 5- gallon (19 liter)

container,.

3. Slowly add the product in small increments to the

water while mixing well with a jiffy-type mixer to a

homogenous consistency.

4. Mix for a minimum of 3 to 5 minutes. Additional

water or material may be added to adjust

workability and desired consistency.

5. Let mixed material stand to allow it to take it’s

initial set for 5 – 10 minutes.

6. Re-mix the material adding enough water to reach

the desired consistency. Do not over mix.

Application

1. For use as an adhesive SA-410 shall be applied to the

back of stone which shall be applied to properly

prepared substrates with enough product to promote

total adhesion. Allow the SA-410 to completely cure

(24 hours is recommended) before filling joints.

2. For use as an adhesive we recommend a margin

trowel or similar type trowel to fully cover the back

of stone. A small amount of SA-410 should be visible

squeezing out from edges of the stone.

3. For use to fill joints in between stones it is

recommended to use a vinyl bag with applicator tip

to squeeze the mixture into voids between stones.

Allow to dry to touch before tooling or raking the

joints. Finish up by brushing with a sift brush or

slicking joints with a slicker tool.

Clean-up

Use fresh water to clean tools or droppings before product

dries.

Distributed by:

Stucco Depot llc

150 North Plains Industrial Rd.

Wallingford, CT 06492

203-430-9186

www.stuccodepot.org

stuccodepot.org@gmail.com





© TTWS